24V Control Module, 7 Connectors, 4-Wire Throttle, Fits for Razor E100(V10+), E125 (V10+), E150 (All Version), eSpark(All Version), Trikke E2 (All Version), Model: ZK2400-DP-LD (ZK2400-DP-FS)

2024-04-06 06:29:16








24V Control Module, 7 Connectors, 4-Wire Throttle, Fits for Razor E100(V10+), E125 (V10+), E150 (All Version), eSpark(All Version), Trikke E2 (All Version), Model: ZK2400-DP-LD (ZK2400-DP-FS)

Specification: This 24V Control Module has 7 connectors (5 plastic connectors & 2 metal connectors). The throttle connection is 4 wire.Fits the following Razor models: E100(versions 10 and up), E125(versions 10 and up), E150(versions 1 and up), eSpark( all versions ), Trikke E2(versions 1 and up)Replace Razor Part : W13111612015. Model No: ZK2400-DP- LD (ZK2400-DP-FS) Note: Please choose the right model according to your needs, because the inappropriate model can not be used.Razor E100 is different from Razor Power Core E100. NOTE: Most electric scooters and electric bikes have controllers which were made specifically for that model. Please carefully confirm the model number of controllers before buying.If a controller is available that will plug-and-play directly into an electric scooter or bike, however the controller is not listed by make and model, be careful when installing it because the wiring patterns going to the connectors may be different than that of the original controller. Double check the wiring to make sure that it is correct before installing the new controller. If the connectors are correct but the wiring going to the connectors are incorrect the pins can be removed and installed in different locations on the connector.Sometimes the brake switch becomes defective and locks into the on position which makes the controller turn off the motor. If the scooter works after disconnecting the brake switch then the brake switch is defective. Controller Installation Tips: 1. Before replacing the controller make sure that the key switch or power switch is in the off position. 2. Disconnect the battery pack from the controller first when removing a controller, and connect the battery pack to the controller last when installing a controller. 3. Hang or block the rear wheel off the ground, or remove the chain or belt from the motor before connecting the battery pack to the controller. Sometimes due to damaged or incorrect wiring or faulty electrical components the rear wheel might spin uncontrollably when making the final wiring connection to the battery pack. 4. Do not short-circuit the battery terminals or wiring harness connector pins and make sure the batteries fit snug into place and that all of the wiring and connectors are in good serviceable condition. Model versions can be determined based on the 8-digit product ID code on your Razor product, can be found on the rectangular white sticker on the handlebar stem, side of the scooter deck, underneath the scooter, on the original battery charger, battery cover or on the bottom of the frame, on the cardboard box in which your scooter came. The last two digits are the version number (e.g. "01"=version 1, "02"=version 2, etc.) IMPORTANT PRODUCT INSTALLATION INFORMATION: The E100 / E125 Series Razor Scooters are a PUSH START Scooter. In order to engage the Motor, You need to push the Scooter, and twist the Throttle! This 24 Volt Controller is Compatible ONLY with Razor E100 - E125 Versions 10 and up, E150 Version 1 and up, eSpark(All Versions),and Trikke E2 (All Versions). Read more 12V Control Module for Razor Power Core E90, Model No: ZK1200-DH 24V Control Module for Razor Power Core E100, Model No: ZK2400-DH 24V Control Module for Razor Ground Force Go Kart, Model: HB2430-TYD6K-FS-ROHS 24V Control Module for Razor Dirt Quad Version11+, Model: HB2430-TYD6-FS-ROHS 36V Controller for Razor MX500(V2 (V14+), Model: HB3650-TYD6-FS-ROHS

Product Features

  • Replacement 24V controller with 4-wire throttle connector
  • COMPATIBLE ONLY WITH: Razor E100 & E125 Versions 10 and up, E150 All Versions, and eSpark(All Versions), Trikke E2 All Versions
  • Replace Razor part #: W13111612015, Model No: ZK2400-DP-LD (ZK2400-DP-FS)
  • The E100 series Razor scooter is a PUSH START scooter. You need to push the scooter, twist the throttle and then the motor will engage
  • Not Compatible With Powercore E100; 1-Year Warranty - Money-back satisfaction guarantee

Tags:cocoon

Title - Default Title

如果有任何关于网站的意见,可以QQ联系或者发邮箱。

tags - tags - tags - tags - tags - tags - tags - tags - tags - tags - tags - tags - tags - tags - tags -