JVCC DC-UHB25FA-G Ultra High Bond Double-Sided Tape [Grey Foamed Acrylic - 25 mil]: 1/4 in. x 36 yds. (Grey)
Size:1/4 in. x 36 yds. (6.3mm wide) JVCC DC-UHB25FA-G Ultra High Bond Double- Sided Tape is constructed of a grey foamed acrylic system which has excellent all-around bonding properties which allows for very high performance in the most demanding of applications. The pressure-sensitive acrylic composition has very good tack; has excellent adhesion to a variety of surfaces; and has high shear strength performance. The double-sided (AKA double-coated) tape is carried on a red, release coated polyethylene liner that is easily removed. Has good UV resistance. Tape will bond to most surfaces including many plastics, composites, sealed woods, and metals; however thorough evaluation is recommended when bonding to low energy surface material such as Polyethylene, Polypropylene, silicones, and Teflon. For lower energy surfaces may need to use an adhesive promoter/primer such as IPA (isopropanol) on the substrate prior to application. When applying the tape after removing the release liner be careful not to contaminate the acrylic adhesive and try to immediately bond the tape to the surface without entrapping air between the tape and the surface it is being applied to. At a minimum application-pressure should be 15 pounds per inch of tape width in order to achieve maximum bond strength. The dwell time the tape needs to be in contact with both surfaces before it reaches its maximum adhesion is 1 to 24 hours. If not otherwise specified widths shown in dropdown are in inches. NOTES: Sizes shipped will typically be the tape industry standard metric-cut sizes, i.e. 24mm for each 1 inch of nominal tape width ordered (rolls are approximately 5% narrower than the nominal size). This product's actual size is 6.3mm wide. As with any adhesive tape product it is always the user's responsibility to determine that the product is suitable for their intended use; e.g. if you want to remove a product cleanly from a specific type of substrate please test on an inconspicuous area first. The color name grey can
Product Features
- JVCC DC-UHB25FA-G Ultra High Bond Double-Sided Tape is constructed of a grey foamed acrylic system which has excellent all-around bonding properties which allows for very high performance in the most demanding of applications. The pressure-sensitive acrylic composition has very good tack; has excellent adhesion to a variety of surfaces; and has high shear strength performance.
- The double-sided (AKA double-coated) tape will bond to most surfaces including many plastics, composites, sealed woods, and metals; however thorough evaluation is recommended when bonding to low energy surface material such as Polyethylene, Polypropylene, silicones and Teflon. For lower energy surfaces may need to use an adhesive promoter/primer such as IPA (isopropanol) on the substrate prior to application.
- When applying the tape after removing the release liner be careful not to contaminate the acrylic adhesive and try to immediately bond the tape to the surface without entrapping air between the tape and the surface it is being applied to.
- At a minimum application-pressure should be 15 pounds per inch of tape width in order to achieve maximum bond strength. The dwell time the tape needs to be in contact with both surfaces before it reaches its maximum adhesion is 1 to 24 hours
- Carrier/Backing: foamed acrylic. Adhesive: ultra-high bond acrylic. Release Liner: red polyethylene film. Thickness: 25.2 mils (carrier, adhesive). Adhesion: 120 ounces per inch (to stainless steel test panel). Tensile Strength: 108 pounds per inch (longitudinal). Service/Operating Temperature: -40F to 212F. Dynamic Shear Strength: 102 pounds per square inch. Short Term Temperature Resistance: up to 320F. Core: 3-inch diameter plastic.
Tags:ship02
Size - 1/4 in. x 36 yds. (6.3mm wide)